Sharp MX M200D Error Codes

Sharp MX M200D Error Codes

Sharp MX M200D Error Codes
Sharp MX M200D Error Codes

This list of Sharp MX M200D Error Codes is intended to be used for information purposes.

When the machine displays an error code there is a functional problem with the machine. Sometimes the code can be cleared by turning the machine off for a minute and then powering the machine back up.  When powering down the machine, first turn off the on/off switch on the operation panel. This allows the machine to perform and complete its power down sequence. Wait until the panel has gone dark and any flashing buttons have stopped flashing. Then turn off the main power switch. Wait for a minute and turn the machine back on, first by the main power switch, then the on/off switch on the operation panel. If the code reappears call your service provider and inform them of the code that is displaying on the operation panel.

E1

E1 00 IMC PWB COMMUNICATION TROUBLE

  • Abnormality occurs in communication between MCU PWB and the IMC PWB
  • IMC PWB-MCU PWB harness abnormality
  • MCU PWB connector disconnection
  • IMC PWB ROM defect/data abnormality
  • Check Connection of the connector and the harness between the IMC PWB and the MCU PWB. Check the ROM of the IMC PWB

E1 10 IMC PWB TROUBLE

  • An Abnormality occurs in the IMC PWB
  • USB Chip error/CODEC error on the IMC PWB
  • Replace the IMC PWB with a new one.

E1 11 IMC ASIC ERROR

  • An abnormality occurs in the IMC PWB
  • Abnormaility on the IMC PWB
  • Replace the IMC PWB with a new one

E1 13 IMC PWB FLASH ROM ERROR

  • An abnormality occurs in the IMC Flash ROM
  • IMC PWB abnormality
  • Replace the IMC PWB with a new one. If downloading of the program is abnormally terminated it may cause an error. Download the program again to avoid this.

E1 16 IMC PWB DIMM MEMORY READ/WRITE CHECK ERROR

E1 81 INTERFACE ERROR IN COMMUNICATION WITH IMC PWB (PARITY)

E1 82 INTERFACE ERROR IN COMMUNICATION WITH IMC PWB(OVERRUN)

E1 84 INTERFACE ERROR IN COMMUNICATION WITH IMC PWB (FRAMING)

E7

E7 01 DUPLEX MODEL MEMORY ERROR

E7 02 LSU TROUBLE

E7 10 SHADING TROUBLE (BLACK CORRECTION)

E7 11 SHADING TROUBLE (WHITE CORRECTION)

E7 12 SHADING TROUBLE

E7 16 ABNORMAL LASER OUTPUT

F2

F2 02 TONER SUPPLY ABNORMALITY

F2 04 IMPROPER CARTRIDGE (DESTINATION ERROR, LIFE CYCLE ERROR)

F2 02 ATC SENSOR ABNORMALITY

F5

F5 02 COPY LAMP LIGHTING ABNORMALITY

F6

F6 00 FAX BOARD COMMUNICATION TROUBLE

F6 10 FAX BOARD TROUBLE

F6 80 FAX BOARD COMMUNICATION TROUBLE (PROTOCOL)

F6 81 FAX BOARD COMMUNICATION TROUBLE (PARITY)

F6 82 FAX BOARD COMMUNICATION TROUBLE (OVERRUN)

F6 84 FAX BOARD COMMUNICATION TROUBLE (FRAMING)

F6 88 FAX BOARD COMMUNICATION TROUBLE (TIME OUT)

F6 99 MACHINE - FAX LANGUAGE ERROR

F9

F9 00 MX-NB10 COMMUNICATION TROUBLE

H2

H2 00 THERMISTOR OPEN

H3

H3 00 HEAT ROLLER HIGH TEMPERATURE DETECTION

H4

H4 00 HEAT ROLLER LOW TEMPERATURE DETECTION

H5

H5 01 5 TIMES CONTINUOUS DETECTIONS OF POUT NOT-REACHED JAM

L1

L1 00 SCANNER FEED TROUBLE

L3

L3 00 SCANNER RETURN TROUBLE

L4

L4 01 MAIN MOTOR LOCK DETECTION

L4 11 SHIFTER MOTOR TROUBLE

L6

L6 10 POLYGON MOTOR LOCK DETECTION

L8

L8 01 NO FULL WAVE SIGNAL

U1

U1 03 FAX BOARD BATTERY ERROR

U2

U2 04 EEPROM READ/WRITE ERROR (SERIAL COMMUNICATION ERROR)

U2 11 COUNTER CHECK SUM ERROR (EEPROM)

U2 40 CRUM CHIP COMMUNICATION ERROR

U9

U9 00 PANEL BOARD COMMUNICATION TROUBLE

U9 80 PANEL BOARD COMMUNICATION TROUBLE (PROTOCOL)

U9 81 PANEL BOARD COMMUNICATION TROUBLE (PARITY)

U9 82 PANEL BOARD COMMUNICATION TROUBLE (OVERRUN)

U9 84 PANEL BOARD COMMUNICATION TROUBLE (FRAMING)

U9 88 PANEL BOARD COMMUNICATION TROUBLE (TIME OUT)

U9 99 PANEL LANGUAGE ERROR

- -

AUDITOR NOT READY

CH ON

DOOR OPEN

CH BLINK

DEVELOPING CARTRIDGE INSTALLED

 

End of Sharp MX M200D Error Codes List