SHARP MX M350U ERROR CODES

SHARP MX M350U ERROR CODES

Sharp MX M350U Error Codes
Sharp MX M350U Error Codes

When the machine displays an error code there is a functional problem with the machine. Sometimes the code can be cleared by turning the machine off for a minute and then powering the machine back up.  When powering down the machine, first turn off the on/off switch on the operation panel. This allows the machine to perform and complete its power down sequence. Wait until the panel has gone dark and any flashing buttons have stopped flashing. Then turn off the main power switch. Wait for a minute and turn the machine back on, first by the main power switch, then the on/off switch on the operation panel. If the code reappears call your service provider and inform them of the code that is displaying on the operation panel.

C1

C1 10 MAIN CHARGER TROUBLE

E6

E6 11 CSI SHADING TROUBLE (WHITE CORRECTION)

E6 14 CIS COMMUNICATION TROUBLE

E7

E7 01 SYSTEM DATA TROUBLE

E7 02 LASER TROUBLE

E7 03 HDD TROUBLE

E7 06 DECODE ERROR TROUBLE

E7 10 SHADING ERROR (BLACK CORRECTION)

E7 11 SHADING ERROR (WHITE CORRECTION ALL PIXEL ADJUSTMENT)

E7 17 SPF SCANNING POSITION ADJUSTMENT TROUBLE (DETECTED ONLY WHEN EXECUTING AND ADJUSTMENT SIM)

E7 50 LSU CONNECTION TROUBLE

E7 60 CONTROLLER SKATING TROUBLE

E7 80 COMMUNICATION TROUBLE (ICU  DETECTION) BETWEEN ICU AND SCANNER

E7 90 COMMUNICATION TROUBLE (ICU DETECTION) BETWEEN ICU AND PCU

F1

F1 00 FINISHER COMMUNICATION TROUBLE

F1 02 FINISHER TRANSPORT MOTOR ABNORMALITY

F1 03 CONSOLE FINISHER PADDLE MOTOR TROUBLE

F1 06 CONSOLE FINISHER SLIDE MOTOR TROUBLE

F1 08 FINISHER STAPLE SHIFT MOTOR TROUBLE

F1 10 FINISHER STAPLE MOTOR TROUBLE

F1 11 FINISHER BUNDLE EXIT MOTOR TROUBLE

F1 12 MAIL BIN STACKER GATE TROUBLE

F1 15 FINISHER LIFT MOTOR TROUBLE

F1 19 FINISHER FRONT ALIGNMENT MOTOR TROUBLE

F1 20 FINISHER REAR ALIGNMENT MOTOR TROUBLE

F1 30 CONSOLE FINISHER COMMUNICATION TROUBLE

F1 31 CONSOLE FINISHER FOLD SENSOR TROUBLE

F1 32 COMMUNICATION TROUBLE BETWEEN THE CONSOLE FINISHER AND THE PUNCH UNIT

F1 33 CONSOLE FINISHER PUNCH SIDE REGISTRATION MOTOR TROUBLE

F1 34 CONSOLE FINISHER PUNCH MOTOR TROUBLE

F1 34 CONSOLE FINISHER PUNCH SIDE REGISTRATION SENSOR TROUBLE

F1 36 CONSOLE FINISHER PUNCH TIMING SENSOR TROUBLE

F1 37 CONSOLE FINISHER BACKUP RAM TROUBLE

F1 38 CONSOLE FINISHER PUNCH BACKUP RAM TROUBLE

F1 39 CONSOLE FINISHER PUNCH DUST SENSOR TROUBLE

F1 40 CONSOLE FINISHER PUNCH POWER INTERUPTION TROUBLE

F1 80 FINISHER POWER ABNORMALITY

F1 81 CONSOLE FINISHER TRANSPORT MOTOR ABNORMALITY

F1 87 FINISHER STAPLE ROTATION MOTOR TROUBLE

F2

F2 00 TONER CONTROL SENSOR OPEN / SENSOR TROUBLE

F2 02 TONER SUPPLY ABNORMALITY

F2 04 IMPROPER CARTRIDGE (LIFE CYCLE ERROR, ETC)

F2 05 CRUM ERROR

F2 06 CRUM ID ERROR

F2 39 PROCESS THERMISTOR TROUBLE

F3

F3 12 MACHINE NO.1 TRAY LIFT-UP TROUBLE

F3 22 MACHINE TRAY 2 LIFT-UP TROUBLE

F6

F6 00 COMMUNICATION TROUBLE (ICU DETECTION) BETWEEN ICU AND FAX

F6 01 FAX EXPANSION FLASH MEMORY ABNORMALITY (ICU DETECTION)

F6 04 FAX MODEM OPERATION ABNORMALITY

F6 20 FAX WRITE PROTECT CANCEL

F6 21 COMBINATION ABNORMALITY OF THE TEL/LIU PWB AND THE FAX SOFT SWITCH

F6 97 FAX BOX SKATING TROUBLE

F6 98 COMBINATION ERROR OF THE FAX BOX DESTINATION AND THE MACHINE DESTINATION INFORMATION

F7

F7 01 FAX BOARD EEPROM READ/WRITE ERROR

H2

H2 00 THERMISTOR OPEN (HL1)

H2 01 THERMISTOR OPEN (HL2)

H3

H3 00 FUSING SECTION HIGH TEMPERATURE TROUBLE (HL1)

H3 01 FUSING SECTION HIGH TEMPERATURE TROUBLE (HL2)

H4

H4 00 FUSING SECTION LOW TEMPERATURE TROUBLE (HL1)

H4 01 FUSING SECTION LOW TEMPERATURE TROUBLE (HL2)

H5

H5 01 5 TIME CONTINUOUS POD 1 NOT-REACHING JAM DETECTION

L1

L1 00 SCANNER FEED TROUBLE

L3

L3 00 SCANNER RETURN TROUBLE

L4

L4 01 MAIN MOTOR LOCK DETECTION

L4 02 DRUM LOCK DETECTION

L4 30 CONTROLLER FAN MOTOR LOCK DETECTION

L6

L6 10 POLYGON MOTOR LOCK DETECTION

L8

L8 01 NO FULL WAVE SIGNAL

L8 02 FULL WAVE SIGNAL WIDTH ABNORMALITY

U1

U1 01 FAX BATTERY ABNORMALITY

U1 02 RTC READ ABNORMALITY (COMMON WITH FAX ON ICU PWB)

U2

U2 00 EEPROM READ/WRITE ERROR (ICU)

U2 11 COUNTER CHECK SUM ERROR (ICU)

U2 12 ADJUSTMENT VALUE CHECK SUM ERROR (ICU)

U2 22 SRAM MEMORY CHECK SUM ERROR (ICU)

U2 23 SRAM MEMORY INDIVIDUAL DATA CHECK SUM ERROR (ICU)

U2 50 HD SECTION INDIVIDUAL DATA CHECK SUM ERROR (ICU)

U2 80 EEPROM READ/WRITE ERROR (SCANNER)

U2 81 MEMORY CHECK SUM ERROR (SCANNER)

U2 90 EEPROM READ/WRITE ERROR (PCU)

U2 91 MEMORY CHECK SUM ERROR (PCU)

U6

U6 00 DESK/LCC COMMUNICATION TROUBLE

U6 01 DESK/LCC NO.1 TRAY LIFT-UP TROUBLE

U6 02 DESK NO.2 TRAY/LCC1 LIFT-UP TROUBLE

U6 03 DESK NO.3 TRAY/LCC2 LIFT-UP TROUBLE

U6 10 DESK/LCC TRANSPORT MOTOR TROUBLE

U7

U7 00 RIC COMMUNICATION TROUBLE

CH

CH - - DOOR OPEN (CH ON)

CH 00 NO DEVELOPER CARTRIDGE

CH 01 NO TONER CARTRIDGE

CH 02 NO DRUM CARTRIDGE

EE

EE EL AUTO DEVELOPER ADJUSTMENT TROUBLE (OVER-TONER)

EE EU AUTO DEVELOPER ADJUSTMENT TROUBLE (UNDER-TONER)

PC

PC - - PERSONAL COUNTER NOT INSTALLED

PF

PF - - RIC COPY INHIBIT SIGNAL IS RECEIVED

- -

- - AUDITOR NOT READY

End of Sharp MX M350U Error Codes List