SHARP MX M450U ERROR CODES
SHARP MX M450U ERROR CODES
When the machine displays an error code there is a functional problem with the machine. Sometimes the code can be cleared by turning the machine off for a minute and then powering the machine back up. When powering down the machine, first turn off the on/off switch on the operation panel. This allows the machine to perform and complete its power down sequence. Wait until the panel has gone dark and any flashing buttons have stopped flashing. Then turn off the main power switch. Wait for a minute and turn the machine back on, first by the main power switch, then the on/off switch on the operation panel. If the code reappears call your service provider and inform them of the code that is displaying on the operation panel.
C1
C1 10 MAIN CHARGER TROUBLE
E6
E6 11 CSI SHADING TROUBLE (WHITE CORRECTION)
E6 14 CIS COMMUNICATION TROUBLE
E7
E7 01 SYSTEM DATA TROUBLE
E7 02 LASER TROUBLE
E7 03 HDD TROUBLE
E7 06 DECODE ERROR TROUBLE
E7 10 SHADING ERROR (BLACK CORRECTION)
E7 11 SHADING ERROR (WHITE CORRECTION ALL PIXEL ADJUSTMENT)
E7 17 SPF SCANNING POSITION ADJUSTMENT TROUBLE (DETECTED ONLY WHEN EXECUTING AND ADJUSTMENT SIM)
E7 50 LSU CONNECTION TROUBLE
E7 60 CONTROLLER SKATING TROUBLE
E7 80 COMMUNICATION TROUBLE (ICU DETECTION) BETWEEN ICU AND SCANNER
E7 90 COMMUNICATION TROUBLE (ICU DETECTION) BETWEEN ICU AND PCU
F1
F1 00 FINISHER COMMUNICATION TROUBLE
F1 02 FINISHER TRANSPORT MOTOR ABNORMALITY
F1 03 CONSOLE FINISHER PADDLE MOTOR TROUBLE
F1 06 CONSOLE FINISHER SLIDE MOTOR TROUBLE
F1 08 FINISHER STAPLE SHIFT MOTOR TROUBLE
F1 10 FINISHER STAPLE MOTOR TROUBLE
F1 11 FINISHER BUNDLE EXIT MOTOR TROUBLE
F1 12 MAIL BIN STACKER GATE TROUBLE
F1 15 FINISHER LIFT MOTOR TROUBLE
F1 19 FINISHER FRONT ALIGNMENT MOTOR TROUBLE
F1 20 FINISHER REAR ALIGNMENT MOTOR TROUBLE
F1 30 CONSOLE FINISHER COMMUNICATION TROUBLE
F1 31 CONSOLE FINISHER FOLD SENSOR TROUBLE
F1 32 COMMUNICATION TROUBLE BETWEEN THE CONSOLE FINISHER AND THE PUNCH UNIT
F1 33 CONSOLE FINISHER PUNCH SIDE REGISTRATION MOTOR TROUBLE
F1 34 CONSOLE FINISHER PUNCH MOTOR TROUBLE
F1 34 CONSOLE FINISHER PUNCH SIDE REGISTRATION SENSOR TROUBLE
F1 36 CONSOLE FINISHER PUNCH TIMING SENSOR TROUBLE
F1 37 CONSOLE FINISHER BACKUP RAM TROUBLE
F1 38 CONSOLE FINISHER PUNCH BACKUP RAM TROUBLE
F1 39 CONSOLE FINISHER PUNCH DUST SENSOR TROUBLE
F1 40 CONSOLE FINISHER PUNCH POWER INTERUPTION TROUBLE
F1 80 FINISHER POWER ABNORMALITY
F1 81 CONSOLE FINISHER TRANSPORT MOTOR ABNORMALITY
F1 87 FINISHER STAPLE ROTATION MOTOR TROUBLE
F2
F2 00 TONER CONTROL SENSOR OPEN / SENSOR TROUBLE
F2 02 TONER SUPPLY ABNORMALITY
F2 04 IMPROPER CARTRIDGE (LIFE CYCLE ERROR, ETC)
F2 05 CRUM ERROR
F2 06 CRUM ID ERROR
F2 39 PROCESS THERMISTOR TROUBLE
F3
F3 12 MACHINE NO.1 TRAY LIFT-UP TROUBLE
F3 22 MACHINE TRAY 2 LIFT-UP TROUBLE
F6
F6 00 COMMUNICATION TROUBLE (ICU DETECTION) BETWEEN ICU AND FAX
F6 01 FAX EXPANSION FLASH MEMORY ABNORMALITY (ICU DETECTION)
F6 04 FAX MODEM OPERATION ABNORMALITY
F6 20 FAX WRITE PROTECT CANCEL
F6 21 COMBINATION ABNORMALITY OF THE TEL/LIU PWB AND THE FAX SOFT SWITCH
F6 97 FAX BOX SKATING TROUBLE
F6 98 COMBINATION ERROR OF THE FAX BOX DESTINATION AND THE MACHINE DESTINATION INFORMATION
F7
F7 01 FAX BOARD EEPROM READ/WRITE ERROR
H2
H2 00 THERMISTOR OPEN (HL1)
H2 01 THERMISTOR OPEN (HL2)
H3
H3 00 FUSING SECTION HIGH TEMPERATURE TROUBLE (HL1)
H3 01 FUSING SECTION HIGH TEMPERATURE TROUBLE (HL2)
H4
H4 00 FUSING SECTION LOW TEMPERATURE TROUBLE (HL1)
H4 01 FUSING SECTION LOW TEMPERATURE TROUBLE (HL2)
H5
H5 01 5 TIME CONTINUOUS POD 1 NOT-REACHING JAM DETECTION
L1
L1 00 SCANNER FEED TROUBLE
L3
L3 00 SCANNER RETURN TROUBLE
L4
L4 01 MAIN MOTOR LOCK DETECTION
L4 02 DRUM LOCK DETECTION
L4 30 CONTROLLER FAN MOTOR LOCK DETECTION
L6
L6 10 POLYGON MOTOR LOCK DETECTION
L8
L8 01 NO FULL WAVE SIGNAL
L8 02 FULL WAVE SIGNAL WIDTH ABNORMALITY
U1
U1 01 FAX BATTERY ABNORMALITY
U1 02 RTC READ ABNORMALITY (COMMON WITH FAX ON ICU PWB)
U2
U2 00 EEPROM READ/WRITE ERROR (ICU)
U2 11 COUNTER CHECK SUM ERROR (ICU)
U2 12 ADJUSTMENT VALUE CHECK SUM ERROR (ICU)
U2 22 SRAM MEMORY CHECK SUM ERROR (ICU)
U2 23 SRAM MEMORY INDIVIDUAL DATA CHECK SUM ERROR (ICU)
U2 50 HD SECTION INDIVIDUAL DATA CHECK SUM ERROR (ICU)
U2 80 EEPROM READ/WRITE ERROR (SCANNER)
U2 81 MEMORY CHECK SUM ERROR (SCANNER)
U2 90 EEPROM READ/WRITE ERROR (PCU)
U2 91 MEMORY CHECK SUM ERROR (PCU)
U6
U6 00 DESK/LCC COMMUNICATION TROUBLE
U6 01 DESK/LCC NO.1 TRAY LIFT-UP TROUBLE
U6 02 DESK NO.2 TRAY/LCC1 LIFT-UP TROUBLE
U6 03 DESK NO.3 TRAY/LCC2 LIFT-UP TROUBLE
U6 10 DESK/LCC TRANSPORT MOTOR TROUBLE
U7
U7 00 RIC COMMUNICATION TROUBLE
CH
CH - - DOOR OPEN (CH ON)
CH 00 NO DEVELOPER CARTRIDGE
CH 01 NO TONER CARTRIDGE
CH 02 NO DRUM CARTRIDGE
EE
EE EL AUTO DEVELOPER ADJUSTMENT TROUBLE (OVER-TONER)
EE EU AUTO DEVELOPER ADJUSTMENT TROUBLE (UNDER-TONER)
PC
PC - - PERSONAL COUNTER NOT INSTALLED
PF
PF - - RIC COPY INHIBIT SIGNAL IS RECEIVED
- -
- - AUDITOR NOT READY
End of Sharp MX M450U Error Codes List